Nanoskin Clay Pads

• Lasts up to 4 times longer than clay bars
• For a flawless “show room perfect” shine
• Glides on & off easily for a slick finish
• If inadvertently dropped on shop floor, simply rinse clean  

Product Detail

NANOSKIN AUTOSCRUB System works fast and achieves professional results with the new advanced rubber polymer technology, which replaces the use of clay bars. With either dual action orbital polisher or hand application, it safely and easily removes paint over spray, water spots, fresh tree sap, rail dust and other bonded surface contaminants from the surface of automotive paint, glass, moldings and plastic. Unlike the clay bar, the AUTOSCRUB can be cleaned by simply rinsing off the accumulated contaminates with water. If you drop the AUTOSCRUB on the ground, no worries, just rinse the sponge pad clean and you're ready to keep using it. Easy glides allows for sturdy and controlled handling, unlike clay bars where constant reshaping is required.

 

 DIRECTIONS:

Use ONLY on clean, cool paint and out of direct sunlight. DO NOT work on the surface below 55°F and over 144°F. Please use in an inconspicuous place for the first time in case of unexpected adverse effects on paint surface.

  1. Thoroughly wash vehicle free of dust, sand, and dirt.
  2. Dilute Clay Lubricant to desired strength.
  3. Mist sufficient Lubricant onto the surface evenly.
  4. Polish the surface with dual action orbital polisher using light pressure (Low Speed).
  5. Wipe off residue with clean dry microfiber towel.

NOTE:Using with 6” soft-edge DA pad is highly recommended.

Sufficient lubrication is crucial to the AUTOSCRUB application.

      Plain water is NOT an adequate lubricant.

      DO NOT use with rotary polisher.

      AUTOSCRUB is not solvent resistant.

      Remove tar & grease before application

 

Helpful Tips:

The AUTOSCRUB has a protective coating to ensure stability within transportation.

To break in the pad, moisten the AUTOSCRUB with desired lubricant.

Moisten a portion of window glass or other glass surface. Rub AUTOSCRUB in circular motion against the glass for 30~60 seconds. You may see a white soapy foam; this is the protective sealant coming off.

Don’t use until the polymerized rubber is soft and slightly tacky.

Cold temperatures may stiffen pad. Warm surface before using.

 

There is a significant difference between NANOSKIN AUTOSCRUB and clay bars. An outstanding machine/advanced polymer combination makes AUTOSCRUB the best contamination removal tool ever.

Visa Mastercard American Express PayPal Diners Club Discover

• Lasts up to 4 times longer than clay bars
• For a flawless “show room perfect” shine
• Glides on & off easily for a slick finish
• If inadvertently dropped on shop floor, simply rinse clean  

Product Detail

NANOSKIN AUTOSCRUB System works fast and achieves professional results with the new advanced rubber polymer technology, which replaces the use of clay bars. With either dual action orbital polisher or hand application, it safely and easily removes paint over spray, water spots, fresh tree sap, rail dust and other bonded surface contaminants from the surface of automotive paint, glass, moldings and plastic. Unlike the clay bar, the AUTOSCRUB can be cleaned by simply rinsing off the accumulated contaminates with water. If you drop the AUTOSCRUB on the ground, no worries, just rinse the sponge pad clean and you're ready to keep using it. Easy glides allows for sturdy and controlled handling, unlike clay bars where constant reshaping is required.

 

 DIRECTIONS:

Use ONLY on clean, cool paint and out of direct sunlight. DO NOT work on the surface below 55°F and over 144°F. Please use in an inconspicuous place for the first time in case of unexpected adverse effects on paint surface.

  1. Thoroughly wash vehicle free of dust, sand, and dirt.
  2. Dilute Clay Lubricant to desired strength.
  3. Mist sufficient Lubricant onto the surface evenly.
  4. Polish the surface with dual action orbital polisher using light pressure (Low Speed).
  5. Wipe off residue with clean dry microfiber towel.

NOTE:Using with 6” soft-edge DA pad is highly recommended.

Sufficient lubrication is crucial to the AUTOSCRUB application.

      Plain water is NOT an adequate lubricant.

      DO NOT use with rotary polisher.

      AUTOSCRUB is not solvent resistant.

      Remove tar & grease before application

 

Helpful Tips:

The AUTOSCRUB has a protective coating to ensure stability within transportation.

To break in the pad, moisten the AUTOSCRUB with desired lubricant.

Moisten a portion of window glass or other glass surface. Rub AUTOSCRUB in circular motion against the glass for 30~60 seconds. You may see a white soapy foam; this is the protective sealant coming off.

Don’t use until the polymerized rubber is soft and slightly tacky.

Cold temperatures may stiffen pad. Warm surface before using.

 

There is a significant difference between NANOSKIN AUTOSCRUB and clay bars. An outstanding machine/advanced polymer combination makes AUTOSCRUB the best contamination removal tool ever.

• Lasts up to 4 times longer than clay bars
• For a flawless “show room perfect” shine
• Glides on & off easily for a slick finish
• If inadvertently dropped on shop floor, simply rinse clean  

Product Detail

NANOSKIN AUTOSCRUB System works fast and achieves professional results with the new advanced rubber polymer technology, which replaces the use of clay bars. With either dual action orbital polisher or hand application, it safely and easily removes paint over spray, water spots, fresh tree sap, rail dust and other bonded surface contaminants from the surface of automotive paint, glass, moldings and plastic. Unlike the clay bar, the AUTOSCRUB can be cleaned by simply rinsing off the accumulated contaminates with water. If you drop the AUTOSCRUB on the ground, no worries, just rinse the sponge pad clean and you're ready to keep using it. Easy glides allows for sturdy and controlled handling, unlike clay bars where constant reshaping is required.

 

 DIRECTIONS:

Use ONLY on clean, cool paint and out of direct sunlight. DO NOT work on the surface below 55°F and over 144°F. Please use in an inconspicuous place for the first time in case of unexpected adverse effects on paint surface.

  1. Thoroughly wash vehicle free of dust, sand, and dirt.
  2. Dilute Clay Lubricant to desired strength.
  3. Mist sufficient Lubricant onto the surface evenly.
  4. Polish the surface with dual action orbital polisher using light pressure (Low Speed).
  5. Wipe off residue with clean dry microfiber towel.

NOTE:Using with 6” soft-edge DA pad is highly recommended.

Sufficient lubrication is crucial to the AUTOSCRUB application.

      Plain water is NOT an adequate lubricant.

      DO NOT use with rotary polisher.

      AUTOSCRUB is not solvent resistant.

      Remove tar & grease before application

 

Helpful Tips:

The AUTOSCRUB has a protective coating to ensure stability within transportation.

To break in the pad, moisten the AUTOSCRUB with desired lubricant.

Moisten a portion of window glass or other glass surface. Rub AUTOSCRUB in circular motion against the glass for 30~60 seconds. You may see a white soapy foam; this is the protective sealant coming off.

Don’t use until the polymerized rubber is soft and slightly tacky.

Cold temperatures may stiffen pad. Warm surface before using.

 

There is a significant difference between NANOSKIN AUTOSCRUB and clay bars. An outstanding machine/advanced polymer combination makes AUTOSCRUB the best contamination removal tool ever.

Seems like you're in . (This is our US/CA store)

Would you like to go to our store?